Specification guide
Audio mixer console evidence before approval
An audio mixer console decision is a document review. Surface width, fader count, I/O card slots and power-supply redundancy are questions for the proposed model. They are not results this page has measured.
Scene recall, motorized faders and redundant supplies appear on some consoles and not on others. Ask the supplier to say which of those features are on the quoted bill of materials. A similar photo is not a feature list.
Request Factory QuotesConsole fields and the record that should carry them
Use a public professional-audio catalog to see how families describe processing. Then replace every value with the proposed manufacturer and model. The inquiry cards name the configurations this desk can forward.
| Check | Unit or condition | Open until |
|---|---|---|
| Working envelope | Width, depth and height in millimeters, plus rear service access | Dimensional drawing of the quoted frame |
| System type | Surface plus stage box, or surface without a stage box, with channel and bus counts | Card list on the quotation |
| Control interface | Local surface, remote software, and any protocol named by the supplier | License and cable lines marked included or excluded |
| Input voltage | Volts, hertz, phase, and whether a second supply is quoted | Power-supply datasheet for that serial family |
| Repeatability | How scene recall is tested, if the model has scenes | Supplier method statement |
| Factory acceptance test | Power-up, channel check, and a deviation sheet | Buyer quality plan plus supplier agreement |
| Noise level and ambient temperature | Fan dBA at a stated distance, operating range in degrees Celsius | Model datasheet, not a room average |
Headline rating versus test basis
A preamp or output figure is a screening hint. It becomes comparable when the level, the bandwidth and the weighting are written. Ask for frequency response such as 20 Hz to 20 kHz at ±1.5 dB, maximum SPL in dB at 1 m when loudspeakers are attached, and coverage in degrees such as 90 horizontal. Continuous power in watts into 8 ohms belongs to an amplifier line. Rated power should name the test percent of THD. If the audio mixer console quote has no amplifier, write not applicable instead of borrowing a wattage from a different SKU. A 19-inch frame is often 483 mm wide; depth and height still need the drawing. Redundant supplies, when offered, should state input voltage such as 100-240 V at 50/60 Hz and the wattage of each supply. Fan noise, when a fan exists, should be dBA at 1 m. Ambient operating range is commonly requested as 0 °C to 40 °C. Ingress protection such as IP20 is an indoor question, not a default.
Standard surface versus a custom I/O load
A catalog surface can reduce the document set. A show that needs a specific card mix, a redundant supply or a stated throughput of simultaneous buses may need a different configuration. Mark mandatory cards separately from preferred ones. Impedance and rigging stay on loudspeaker or mount lines so they do not blur the console comparison.
Purchase price versus delivered scope
Delivered cost adds packaging, freight, the Incoterm, commissioning scope, training, spares and exclusions. A console that ships without a case or without a startup day is not the same commercial object as one that includes both. This desk does not publish a percentage difference between those offers.
How to submit the console package
What belongs in the opening message?
Product family, fader count or an acceptable range, quantity, US destination, requested timing, and the drawings you can share later. Optional budget needs a currency and a per-unit or whole-order basis.
How should supplier preference be worded?
Choose high-end, mid-range, budget or not yet decided. The choice records what the buyer wants to compare. It is not a rating of any factory.
Which files are asked after the model is proposed?
Current datasheet, dimensional drawing, power-supply rating, card list, and any certificate with its model coverage. Ask about ingress protection when the install is damp or outdoors. Most control rooms will record indoor duty instead.
What stays out of this form?
File upload. Send drawings after the desk replies. Also keep loudspeaker coverage, if needed, on a separate requirement so the console approval is not blocked by an unfinished speaker design.
Cross-check the USB interface page when a computer path is part of the surface, and the room page when an analog sidecar remains in the design. The procurement article repeats the comparison table for sharing inside a buying team.
Ask factories to quote the console you described
The action is a factory quotation on the written configuration. Approval of fit, code and final acceptance stays with the buyer qualified people, after they read the returned documents.
Request Factory Quotes